We use Optical Character Recognition (OCR) during our scanning and processing workflow to make the content of each page searchable. You can view the automatically generated text below as well as copy and paste individual pieces of text to quote in your own work.
Text recognition is never 100% accurate. Many parts of the scanned page may not be reflected in the OCR text output, including: images, page layout, certain fonts or handwriting.
566
MOTION PICTURE HANDBOOK
4
— 626P
Pivot base for motor
4
— 652P
frame.
— 627P
Clamp washer for face
4
— 653P
of driving friction
wheel.
4
— ,659P
— 628P
Pulley on shaft of
4
— 660P
driven friction disc.
— 629P
Bushing for driven
2 1
3 — 800P
friction disc shaft.
2
— 822P
— 630P
Bushing for ball
1
— 827P
bearing end of
1
-^829P
driven friction disc.
— 801P
— 631P
Bushing for driving
1
— 833P
shaft on motor
2
— 853P
drive.
2
— 854P
— 632P
Adjusting nut for
3 &
2 — 867P
driven friction disc.
2
— 868P
4
— 633P
Retaining washer on
2
— 872P
hub of driving fric
1
— S96P
4
— 635P
tion wheel. Shaft for driving
1
— <906P
friction wheel.
2
— 866
4
— 639P
Friction lever for
2
— 70
moving friction
3
—801
wheel.
4
— 6 5 OP
Leather band for
4
— 122
flexible coupling.
Rod for speed control.
Ball bearings for friction drive.
Belt for motor drive.
Rawhide pin for driving belt fastener.
Clamp screws.
Stock screw.
Stock screw.
Stock screw.
Clamping screw.
Machine screw, stock.
Stock macQiine screw.
Stock machine screw.
Stock machine screw.
Stock machine screw.
Stock machine screw.
Stock machine screws.
Stock machine screw. Stock machine screw.
Pin.
Nut holding housing 480 to yoke 475.
Pin for hinge of door 336.
American Standard— " Master Model"
No. 1.— To Remove the Gate, loosen screw 525, P. 1, and pull shaft 506, P. 3, out to the right. In order to get at screw 525, P. 1, it may be necessary to take the mechanism loose from its base and stick a screwdriver up through a hole in base casting immediately under the screw. Before starting to take off the gate, drop the framing carriage clear down, or else the gate will not pass the film chute.
No. 2. — To Remove the Lower Sprocket Film Chute, A-P 17, P. 2, and gear 454, P. 2, first follow Instruction No. 1, then drive out the taper pin iri the center of the hub of lower sprocket, 443, P. 2, and the taper pin in the hub of gear 454, P. 2. You can then pull the shaft ut to the left, driving it with a copper punch if necessary. Be sure and drive the taper pin the right way.
No. 3. — To Remove Lower Sprocket 443, P. 2, follow Instruction Nos. 1 and 2.
No. 4. — To Remove Gear, 454, P. 2, follow Instruction Nos. 1 and 2.
No. 5— To Remove Film Slide, A-P 18, P. 2, carrying with it film cradle 382, P. 2, and film guiding spool 536, P. 2, follow Instruction Nos. 1 and 2, ana then remove sciew 527, P. 2, at' the lower end of the film slide, and screws (two of