Educational film guide ()

621.9 EDUCATIONAL FILM GUIDE MILLING MACHINE. Castle 1942 8mln sd *• $17.88 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 Provides a demonstration of a plain milling machine and shows the basic parts of the machine, locates and names the various control levers, and demonstrates the action of the table longitudinally, vertically, and cross-wise "Not a mechanic, I marvel at the clearness of explanations. I felt that I could use the machine if I could but see the film a time or two more." Collaborator PIPE FABRICATION WITH JIGS. Castle 1944 22min sd $33.60 621.9 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 The purpose of the jig and how to plan Its layout is shown; how to lay out and assemble targets for a jig; how to set targets and hangers using a pipe section as a template; and how to fabricate pipe on a jig PLAIN TURNING. SouthBendLathe 1941 20min sd (How to run a lathe) $43, loan; also color $110. loan 621.9 sh-c-tr-ad Guide Produced by Burton Holmes Films Adapted from the company's manual "How to run a lathe" This companion film to "Metal Working Lathe," (above) clearly illustrates all operations in the machining of a shaft held between the lathe centers. It teaches many of the basic procedures encountered In all lathe work. Among these are blue print reading, measuring with calipers and micrometers, locating and drilling center holes, proper selection of cutting tools, rough turning and finish turning of the work-piece PLANING A FLAT SURFACE. Castle 22min sd $33.60 621.9 sh-c-tr-ad Guide Produced by the U.S. Office of Education. Accompanying filmstrip $1 Explains the function of a planer; shows how to prepare the machine and tools PRECISION GAGE BLOCKS. Castle 1944 18min sd $30.01 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 Calculating a stack of gage blocks; how to clean and assemble blocks; various uses of gage blocks in setting inspection gages; and how to store gage blocks when not in use REAMING WITH STRAIGHT HAND REAMERS. Castle 1942 20min sd $32.16 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 "Shows and explains the operations, methods, and procedures used." Business screen REAMING WITH TAPER HAND REAMERS. Castle 1942 15min sd $27.15 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 "Shows and explains the tools, operations, methods, and procedures used. The demonstrations covered are the hand reaming of a taper pin hole through a shaft and collar and taper reaming a dowel pin hole." Business screen ROUGH FACING AND BORING AND TURNING A SHOULDER ON A VERTICAL TURRET LATHE. Castle 1942 22min sd $34.31 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 Reviews the operation of the vertical head; portrays In considerable detail the parts and the operation of the horizontal or side head; depicts the procedures used in holding work on the table with clamps and driving block; and demonstrates the operations used In making rough facing, boring, and turning cuts with the independent use of the main and side head An aluminum casting of an airplane motor part is used for this demonstration ROUGH FACING, TURNING AND DRILLING. Castle 1942 31min sd $43.75 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 Emphasizes the identification of the various controls on a standard vertical turret lathe; the use of these controls in making facing, turning, and drilling cuts with the vertical head; demonstrates the independent and universal movements of the chuck jaws on the table; the method of holding a piece by Internal chucking and the use of the Indexes on the machine to control the movement of the cutting tools The job selected for this machine demonstration is an aluminum casting for a diffuser section of a modern airplane engine ROUGH TURNING BETWEEN CENTERS. Castle 1941 15min sd $27.15 621.9 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 Emphasizes and presents In considerable detail the care and operation of the machine, the identification of the various controls and parts of the machine used in rough turning, the correct setting of rough turning tools, the safety precautions necessary for both operator and machine, and the necessity for following a blueprint in performing any job The job selected for this demonstration Is rough turning a pin of rough stock such as the pins used In rear axle assembly SAVE THOSE TOOLS. IntHarvester 1944 lOmin sd loan 621.9 c-tr-ad "Shows how this particular company's own tool salvage program was organized and Its functioning methods, from salvage at Individual plants to the central clearing house for the utilization of excess and obsolete tools. "Emphasis is given to a low -temperature brazing process of repairing broken or damaged tools of various kinds. Including reamers, drills, slitting saws, broaches, hobs and milling cutters. "Regrlnding of tools to smaller sizes or reworking to different types is also treated." Business screen SAWING AN INTERNAL IRREGULAR SHAPE. Castle 1944 32min sd $44.47 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 This film shows how to drill the saw starting hole; how to make the saw selection; how to set up a band saw machine; how to weld saw bands; how to saw an internal contour shape; and how to remove and store a band saw SAWING TEMPLATE METAL. Castle 1944 17min sd $28.58 621.9 sh-c-tr-ad Guide Produced by U.S. Office of Education. Accompanying filmstrip $1 Shows how to use a job selector chart for width, pitch, set of teeth; and speed; how to identify raker, wave, and straight teeth; how to mount a saw blade on a band saw; how to select and adjust blade guides; how to saw to a layout line; how to "chew out" metal from a notch; and how to remove burrs 452