Educational film guide ()

1949 EDITION 694 FACE PLANING UNEVEN SURFACES— Continued Surfacing of wide stock on one side; using a pusher; making and using a feather board; and how to use a backing block for facing thin stock FACE TURNING A COLLAR. Castle 1945 16min sd J27.88 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Preparing a face plate chuck; how to attach work to face plate chuck; how to turn a fillet; and how to taper turn a recess HAND SAWJNG. JamHandy 1943 20min sd $66 694 sh-tr-ad Gives the fundamentals of handling hand saws and choosing the right saw for the Job JOINTING AN EDGE FOR GLUING— INSTALLING KNIVES. Castle 1945 21min sd $32.87 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Determining when knives are dull; removing dull knives; installing sharp knives on the cutter head and adjusting them for proper cutting; how to straighten crooked stock; and how to joint edges for gluing JOINTING EDGES AND END GRAIN 90 DEGREES TO A FACE. Castle 1945 17min sd $29.29 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Shows how to set the fence and infeed table to proper height; how to feed with the grain; how to joint end grain so as to prevent tearing; and how to observe all necessary safety precautions PLANING ROUGH SURFACES TO DIMENSIONS. Castle 1945 17min sd $29.29 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Adjusting the table for desired thickness; how to set feed rolls for proper speed; how to feed with the grain; and how to surface short pieces and glued stock RABBETING AND SHAPING AN EDGE ON STRAIGHT STOCK. Castle 1945 18min sd $30.01 694 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying fllmstrip $1 Principle of the shaper operation; how to set up the machine for cuttingr rabbets; how to cut rabbets; how to set up the machine to shape molding; and how to shape a molding RIPPING AND CROSSCUTTING. Castle 1945 19min sd $30.74 694 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying fllmstrip $1 Shows how each working part of the variety saw functions; how to check saw blades; how to set the fence; how to protect one's self on the job; how to change saw blades; how to use a cutoff gage; and how to use a hinged block in crosscutting SANDING FLAT AND IRREGULAR SURFACES. Castle 1945 19min sd $30.74 694 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying fllmstrip $1 Belting sander operators; how to prepare a sanding belt; how to sand flat stock on a sander; how to use and replace sandpaper on a disk sander; and how to use and replace aandoaper on a spindle sander SAWING A REVERSE CURVE AND A BEVEL REVERSE CURVE. Castle 1945 18mln sd $30.01 694 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying fllmstrip $1 Selecting and laying out stock to avoid waste: how to reverse curves to contour lines; how to use the table tilting gage; how to saw a beveled, reverse curve; how to prepare a template for a newel post; and how to saw a newel post having reverse curves SAWING WITH JIG AND CHANGING BAND. Castle 1945 20min sd $32.16 694 sh-tr-ad Guide Produced by U.S. Office of Education. Accompanying fllmstrip $1 Selecting the proper band saw blades for the Job; how to change blades; how to fold blades for storage; how to adjust saw sruldes; how to mark stock and cut to the mark; how to prepare a Jig; and how to cut disks, using a Jig SHAPING AFTER TEMPLATE AND SHAPING CURVED EDGES. Castle 1945 17min sd $29.29 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Making a template for the job; how to Install knives in the spindle; how to use the template when smoothing squared edges; how to set up equipment for shaping a curved edge; and how to shape a curved edge in more than one cut TURNING A CYLINDER BETWEEN CENTERS. Castle 1945 17min sd $29.29 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Choosing and centering stock for a Job; how to mount stock in the wood lathe for turning between centers; how to select the proper speed; how to select and use cutting tools; how to use the parting tool to establish diameter and length; how to use the skew chisel; how to sand turning work; and the safety factors involved TURNING TAPER WORK. Castle 1945 12min sd $22.88 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Centering cylindrical wood stock for spindle turning; how to make clearance cuts and why they are made; how to establish the diameters of a taper; how to turn a single taper; how to establish diameters for turning two tapers from a single piece of material; and how to turn the tapers TURNING WORK tN A CHUCK. Castle 1945 15min sd $26.43 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Mounting work on a face plate; how to turn one face of the work; how to make a chuck for the opposite face; how to fit the finished face to the chuck; and how to turn the second face TURNING WORK ON A FACE PLATE. Castle 1945 15min sd $27.15 694 sh-tr-ad Guide Produced by the U.S. Office of Education. Accompanying fllmstrip $1 Various types of face plates; how to choose the proper face plate; how to attach the stock to the face plate; how to true up the work; how to scribe the work for inside turning; how to use the round nose chisel and diamond point chisel; and how to smoothe the bottom of the recess 531